Delivery charges will vary depending on your location.

To find out delivery cost to your postcode, add the products your require to your basket and then review your basket, entering the delivery postcode

We look to dispatch all products same-day where possible, we use a close network of couriers we have worked alongside for a number of years and will share any and all shipping updates with you directly.

Gyproc DriWall Adhesive is a high-quality general purpose adhesive providing increased strength and safety in wall and ceiling applications without leaving weak points. An ideal choice for use with British Gypsum DriLyner systems and fixing plasterboard and levelling uneven walls.

Features of the Gyproc Driwall Adhesive:

It is a functional, waterproof adhesive that has been designed for use with DriLyner systems with high, medium or low suction backgrounds which makes it a very versatile product. Dri-Wall adhesive is quick-drying and helps to erase any nail-pops on the surface. It can also eliminate the use of fasteners by up to 50%.

Supplied in 25kg bags.

How to dot and dab plasterboard

• Mark the ceiling and floor at the thickness of the board plus the adhesive. Also, mark the wall to show where the centre of each board will be.
• Cut the plasterboard 15mm short of the wall height.
• Mix the plasterboard adhesive to a thick consistency. Using a trowel, apply a continuous band around the perimeter of the wall, ceiling edge, and any services or openings.
• Apply the adhesive in dabs that are 50mm to 75mm wide and around 250mm long. Use three vertical rows for each board, with one in the middle and two at least 25mm from the edge. Also, apply a band of adhesive at the skirting level.
• Place the reverse side of the board against the dabs, resting on plasterboard packers. Tap it using a straight edge until it aligns with the marks on the ceiling and floor.
• Using a board lifter, raise the board until it’s tight against the ceiling. Wedge the board into place using plasterboard packers, then remove the lifter.
• Follow the same process for the rest of the room, then remove the plasterboard packers from underneath the boards when the adhesive has been set.

What you need to dot and dab plasterboard

To dot and dab plasterboard, you will use plasterboard, adhesive, and a number of different tools.

Choose boards that are at least 12.5mm thick as they are more rigid, making your walls robust. They should also be as wide as possible to reduce the number of joints you’ll need to cover later on. Consider whether you need extra moisture resistance, thermal performance or sound insulation.

If you’re going to skim with plaster, you can use either square edge (SE) or taper edge (TE) plasterboard. If you will be jointing, use tapered edge boards so it’s easier to get a smooth finish.

You’ll also need equipment for measuring up, cutting the plasterboards, applying the adhesive, and installing and fixing the plasterboard. Don't forget to wear PPE!

How much dot and dab adhesive to use

When calculating how much dot and dab adhesive you’ll need, remember that dabs should be between 50mm and 75mm wide, around 250mm long (the length of a trowel), and about 10mm thick. You’ll need three vertical rows for each board, placing each dab 6 to 8 inches below the last one.

As well as this, you need enough adhesive to apply a band around the perimeter of the wall, ceiling edge, services or openings, and at skirting level.

With Gyproc DryWall Adhesive, each bag will fix approximately two boards. If you don’t use them all immediately, don’t worry; bags last for four months.

How to mix dot and dab adhesive

Using a mixing stick, mix the dot and dab adhesive to a thick consistency so that it provides a firm hold for the plasterboard. This means you need to be careful when adding water; follow the instructions on the packaging for full guidance.

You’ll need a clean bucket so that dirt from previous projects doesn’t mix with the adhesive and make it less effective. Only mix enough for one board at a time, giving you plenty of time to fix each board before the adhesive starts to set.

How long does dot and dab take to dry?