Concrete Lab Mould Release Agent has been developed using the latest water soluble polymer technology to produce anenvironmentally friendly and highly efficient release material for concrete formwork on site. It is ready to use and particularly suited to both indoor and outdoor use on faced sealed plywood, melamine, steel moulds and other impervious formwork materials.
Application
Apply thinly, by spray, brush or swab prior to each concrete pour. Application should be a minimum of 1 hour before pouring, for the excess water to evaporate off and the release film to be properly established. With first application to new formwork a second light coat may be required. On verticalforms any excess material accumulating at the bottom of the form should be removed. On untreated timber surfaces additional coats may be required for first use.
Do not use when temperatures are below freezing.
TIP: Check out the pdf's on the Premix kits page for instructions on how to build moulds. We recommend using melamine for the base, melamine strips for the formwork (external formwork, hob and sink openings etc, plus melamine blocks to support the forms). We use a hot melt glue gun to build our moulds. It is also common to put a 4-8mm round on seen edges of a worktop or table which we create using silicone inside our mould.
Coverage
A thin coating to give a coverage rate of 30 to 50m2 per litre depending upon surface porosity andtexture. Protect from rain when still wet.
Storage
The release agent is a water based product and should be protected from frost. Containers must be keptsealed after use. The product may require mild agitation before use if stored for more than 6 months.
Shelf life- In excess of 12 months in sealed containers, use within 2 months of opening. Roll or agitatecontainers after prolonged storage.
Delivery is free to Mainland England and Wales. Deliveries are chargable to Scotland.
Once the order is placed, our courier will call you within 3 working days to arrange a delivery date. If you do not hear from the courier within 3 days, please get in touch with us. The majority of deliveries are made within 7 days, occasionally a little longer during peak periods.
Deliveries are made between 08:00 and 18:00 on the day, we request the driver calls you one hour before with an advised time.
Delivery is made via a kerbside tail lift lorry, we cannot deliver to sloping ground as the tail lift must be able to lay flat.
The road must be wide enough for a lorry to fit down and free from obstruction, if there are any access restrictions, please contact us.
Deliveries must be signed for, please report any damages to us within 24 hours.
We offer all bricks with a tail lift offloading service, Please familiarise yourself with the information below.
Crane offloading is available as a premium service for some bricks.
FAQ
All of our C16 and C24 graded timber is regularised
Regularised timber is timber that has been processed to have a uniform shape and size. This means that the wood has been sawn and planed to remove any irregularities and ensure that each piece of wood has consistent dimensions. Regularised timber is often used in construction, particularly in the framing of buildings, as it is easier to work with and can be more efficiently installed than irregularly shaped timber.
We have one of the largest ranges of timber lengths, dimensions and grades available to buy online.
The variation you require will determine the exact lead time and delivery method.
Most orders arrive within 3-4 days, the maximum is 7 days. Please get in touch before you order if you need a specifc delivery date.
Delivery charges vary by postcode. To find out the delivery charge, add the item(s) you require to your basket and select CALCULATE SHIPPING at the bottom of the page.
Some orders are delivered on our own vehicles based in Leicestershire and Cheshire. We also use carriers including Yodel and Tuffnells. For some sizes and locations we use regional distributors.
If you'd prefer crane offloading rather than tail lift vehicle offloading for your brick order then this service is available for the majority of bricks that we sell. Charges are shown at checkout.
For deliveries of less than 6 packs then Taillift offloading is normally a more cost effective option
Downloadable information can be found here:
Armstrong Cheshire supply the full range of Catnic Lintels. If you don't see the lintel you need on our website, choose from the Catnic Lintel Selector Brochure and give us a call 01625 322269
Downloadable information can be found here:
Water-Based Mould Release Agent
Concrete Lab Mould Release Agent has been developed using the latest water soluble polymer technology to produce anenvironmentally friendly and highly efficient release material for concrete formwork on site. It is ready to use and particularly suited to both indoor and outdoor use on faced sealed plywood, melamine, steel moulds and other impervious formwork materials.
Application
Apply thinly, by spray, brush or swab prior to each concrete pour. Application should be a minimum of 1 hour before pouring, for the excess water to evaporate off and the release film to be properly established. With first application to new formwork a second light coat may be required. On verticalforms any excess material accumulating at the bottom of the form should be removed. On untreated timber surfaces additional coats may be required for first use.
Do not use when temperatures are below freezing.
TIP: Check out the pdf's on the Premix kits page for instructions on how to build moulds. We recommend using melamine for the base, melamine strips for the formwork (external formwork, hob and sink openings etc, plus melamine blocks to support the forms). We use a hot melt glue gun to build our moulds. It is also common to put a 4-8mm round on seen edges of a worktop or table which we create using silicone inside our mould.
Coverage
A thin coating to give a coverage rate of 30 to 50m2 per litre depending upon surface porosity andtexture. Protect from rain when still wet.
Storage
The release agent is a water based product and should be protected from frost. Containers must be keptsealed after use. The product may require mild agitation before use if stored for more than 6 months.
Shelf life- In excess of 12 months in sealed containers, use within 2 months of opening. Roll or agitatecontainers after prolonged storage.
Delivery is free to Mainland England and Wales. Deliveries are chargable to Scotland.
Once the order is placed, our courier will call you within 3 working days to arrange a delivery date. If you do not hear from the courier within 3 days, please get in touch with us. The majority of deliveries are made within 7 days, occasionally a little longer during peak periods.
Deliveries are made between 08:00 and 18:00 on the day, we request the driver calls you one hour before with an advised time.
Delivery is made via a kerbside tail lift lorry, we cannot deliver to sloping ground as the tail lift must be able to lay flat.
The road must be wide enough for a lorry to fit down and free from obstruction, if there are any access restrictions, please contact us.
Deliveries must be signed for, please report any damages to us within 24 hours.
We offer all bricks with a tail lift offloading service, Please familiarise yourself with the information below.
Crane offloading is available as a premium service for some bricks.
All of our C16 and C24 graded timber is regularised
Regularised timber is timber that has been processed to have a uniform shape and size. This means that the wood has been sawn and planed to remove any irregularities and ensure that each piece of wood has consistent dimensions. Regularised timber is often used in construction, particularly in the framing of buildings, as it is easier to work with and can be more efficiently installed than irregularly shaped timber.
We have one of the largest ranges of timber lengths, dimensions and grades available to buy online. The variation you require will determine the exact lead time and delivery method.
Most orders arrive within 3-4 days, the maximum is 7 days.
Please get in touch before you order if you need a specific delivery date.
Delivery charges vary by postcode. To find out the delivery charge, add the item(s) you require to your basket and select CALCULATE SHIPPING at the bottom of the page. Some orders are delivered on our vehicles based in Leicestershire and Cheshire. We also use carriers including Yodel and Tuffnells. For some sizes and locations, we use regional distributors.
If you'd prefer crane offloading rather than tail lift vehicle offloading for your brick order then this service is available for the majority of bricks that we sell. Charges are shown at checkout.
For deliveries of less than 6 packs then Taillift offloading is normally a more cost effective option
Downloadable information can be found here:
Armstrong Cheshire supply the full range of Catnic Lintels. If you don't see the lintel you need on our website, choose from the Catnic Lintel Selector Brochure and give us a call 01625 322269
Delivery charges will vary depending on your location.
To find out delivery cost to your postcode, add the products your require to your basket and then review your basket, entering the delivery postcode
We look to dispatch all products same-day where possible, we use a close network of couriers we have worked alongside for a number of years and will share any and all shipping updates with you directly.
Share information about this product with your customers.
Water-Based Mould Release Agent
Concrete Lab Mould Release Agent has been developed using the latest water soluble polymer technology to produce anenvironmentally friendly and highly efficient release material for concrete formwork on site. It is ready to use and particularly suited to both indoor and outdoor use on faced sealed plywood, melamine, steel moulds and other impervious formwork materials.
Application
Apply thinly, by spray, brush or swab prior to each concrete pour. Application should be a minimum of 1 hour before pouring, for the excess water to evaporate off and the release film to be properly established. With first application to new formwork a second light coat may be required. On verticalforms any excess material accumulating at the bottom of the form should be removed. On untreated timber surfaces additional coats may be required for first use.
Do not use when temperatures are below freezing.
TIP: Check out the pdf's on the Premix kits page for instructions on how to build moulds. We recommend using melamine for the base, melamine strips for the formwork (external formwork, hob and sink openings etc, plus melamine blocks to support the forms). We use a hot melt glue gun to build our moulds. It is also common to put a 4-8mm round on seen edges of a worktop or table which we create using silicone inside our mould.
Coverage
A thin coating to give a coverage rate of 30 to 50m2 per litre depending upon surface porosity andtexture. Protect from rain when still wet.
Storage
The release agent is a water based product and should be protected from frost. Containers must be keptsealed after use. The product may require mild agitation before use if stored for more than 6 months.
Shelf life- In excess of 12 months in sealed containers, use within 2 months of opening. Roll or agitatecontainers after prolonged storage.
Concrete Lab Mould Release Agent has been developed using the latest water soluble polymer technology to produce anenvironmentally friendly and highly efficient release material for concrete formwork on site. It is ready to use and particularly suited to both indoor and outdoor use on faced sealed plywood, melamine, steel moulds and other impervious formwork materials.
Application
Apply thinly, by spray, brush or swab prior to each concrete pour. Application should be a minimum of 1 hour before pouring, for the excess water to evaporate off and the release film to be properly established. With first application to new formwork a second light coat may be required. On verticalforms any excess material accumulating at the bottom of the form should be removed. On untreated timber surfaces additional coats may be required for first use.
Do not use when temperatures are below freezing.
TIP: Check out the pdf's on the Premix kits page for instructions on how to build moulds. We recommend using melamine for the base, melamine strips for the formwork (external formwork, hob and sink openings etc, plus melamine blocks to support the forms). We use a hot melt glue gun to build our moulds. It is also common to put a 4-8mm round on seen edges of a worktop or table which we create using silicone inside our mould.
Coverage
A thin coating to give a coverage rate of 30 to 50m2 per litre depending upon surface porosity andtexture. Protect from rain when still wet.
Storage
The release agent is a water based product and should be protected from frost. Containers must be keptsealed after use. The product may require mild agitation before use if stored for more than 6 months.
Shelf life- In excess of 12 months in sealed containers, use within 2 months of opening. Roll or agitatecontainers after prolonged storage.
